Every place I've ever lived has been designed for that "average American family," with lots of bedrooms, living room, dining room, family room, etc. The problem was that I was a single person, not an average family. I needed space, but for hobbies, not people. And because I'm over 6'2", bending over to use sinks designed for children was a constant frustration. Over the years, I collected a list of things I would change if I could have my dream house. As I approached retirement, I realized time was running out for that house; it was now or never.
Dreams are not always perfect, however. I could never afford my dream house, a spacious Southern California home overlooking the Pacific Ocean. But I could afford a modest ranch house, with a 20-mile drive to the beach. It was a very long way from perfect, but it had potential.
This blog documents the process of turning that small average house into something that matches my lifestyle. It will be as close to my dream house as I can make it. I'm doing all the work myself to stretch my resources. By not hiring contractors, I can afford high quality materials, and I'll know the job is always done right. The remodeling will be my primary avocation for a few years, even as I try to fit in my writing and other hobbies.
It promises to be an interesting journey, and a challenging one!
Sunday, March 25, 2018
PotteryStudio Cabinets — Part 2
At the end of the last post, the two cabinets that make up the whole were in place, the left one attached and the right one just sitting there looking pretty:
With the back installed on the right half, and it screwed into the studs and base, I started work on the shelf connecting the two (didn't want to waste that space — good for storing pottery trimming chucks — I'll explain later). I also started to fit some of the birch trim, but discovered my stock of birch was low, so another trip down to the wood store was needed.
With the cabinets in place, I fabricated the counter top. It was about nine inches longer than eight feet, so I had to carefully glue (with reinforcing biscuits) an extension. I screwed on a couple of temporary braces while carrying the long piece from the garage to the pottery studio. Just a little awkward.
Where the plywood spanned the space between the two counters, I glued and screwed more plywood to the underside of the counter top (flipping it over to do that).
The top right-side up for a test fitting:
It was time to glue the plastic laminate top to the plywood. It was too cold outside, so I set up two makeshift tables in the pottery studio — one for the plastic laminate and the other for the plywood. The contact cement is applied to both surfaces and left to dry. Then the laminate is placed on top of the plywood, but separated by wooden dowels to keep them from touching. Once they touch, they can't be adjusted. The dowels keep them apart while they are aligned in position. Then the dowels are removed beginning from the center toward the ends.
A roller is used to apply high pressure to ensure a good bond without any air bubbles trapped between laminate and plywood, again, working from the center toward the ends until the laminate is fully cemented. The laminate is cut slightly larger than the plywood; the small overlap is removed with a small router (laminate trimmer) fitted with a carbide straight cutting bit (with guide bearing).
Then the top is moved back into place and attached to the cabinets with screws (from the bottom).
At this point, I started attaching the birch trim on the edges of the plywood, using biscuits (for some pieces), glue, and finish nails. I also worked on the birch backsplash. I again ran out of birch, which has both light and dark coloration, and decided to substitute maple for the last bits rather than make a special trip to the wood store (hour drive each way).
Next I started on the drawers. Not all sixteen of them, mind you, but four of the larger ones, which would be made of plywood. Because the large drawers could be holding fifty pounds of clay, I opted to install a 3/4" plywood base. To avoid the problems I had with the half-inch plywood sides delaminating with the drawer bottom dado, I simply glued and screwed the half-inch sides to the edge of the 3/4" base.
I use plywood for the deep drawers because finding wide solid wood that stays straight and flat is difficult. That said, it adds complications. The edges have to be covered with trim that also stiffens the sides, and I have to make from scratch the maple trim I use (a real pain and consumer of time).
Here's the type of joint I use for the plywood drawers (viewed from the bottom). I'll start using dovetail joints when I get to the shallower drawers that have solid wood sides.
And of course gluing the trim on takes time (and there are a lot of drawers).
So jumping ahead to where I am now, this is the half of the pottery studio where the cabinets are. This half also houses the sink and the kiln (to be ordered in a couple of days). The kiln will sit on the right where the spot light is shining on the floor.
Here's a photo showing the both sides:
So I've just made the four plywood drawers and put the plain white painted fronts on three of them.
And the two on the right side of the cabinet, one with the front on and the other without.
This is the cabinet as it now stands. You can see the birch backsplash, installed with silicone adhesive. The side splashes are actually made of maple.
I also made a couple more of the side-loading kitchen drawers. The first photo shows the carcasses, and the other two photos show them with the fronts attached.
As I mentioned, I will drive down to San Diego to order the kiln in a couple of days, and continue building drawers. This time I'll be setting up my dovetail jig and hopefully cranking out drawers for both the pottery studio and the kitchen. Also on the horizon is more bamboo flooring, this time for the living room.
Saturday, February 10, 2018
Pottery Studio Cabinets — Part 1
When I began to cut out the pieces for the cabinets, I noticed that my expensive sheets of plywood had warped. Cutting them was not a problem, but cutting the dados (grooves) and interlocking tongues was. Before making these cuts, I adjust the position and depth of the cut, using scrap pieces plywood. But pushing the whole cabinet parts through the dado blade becomes a problem when the piece is bowed up. You have to push down hard to keep the plywood flat against the table, all the while repositioning your hands to feed the piece through the blade. If the plywood rises up as you shift your hands, the groove will be cut too shallow.
So some pieces needed to be run through multiple times.
The bigger problem was that warped (curved) cabinet sides do not slide into straight dados. That meant I had to clamp a 2x4 on the edge of the plywood to straighten it, and then insert the tenon into the dado. But then, as I discovered to my dismay, when I removed the 2x4, the plywood sprung back and tore out the side of the dado.
So then I had to glue that together. The drawer slides also demanded straight cabinet sides. As a solution, I had to cut twenty wood cleats (for the two cabinets) that I could glue and screw onto the warped plywood, and then glue and screw the curved plywood to the straight cleats.
That worked, but it meant that instead of assembling the whole cabinet in one step, I would have to assemble a couple of pieces at a time, and then wait a day until the glue dried to full strength before adding another piece. Lots of clamps to keep everything straight. And keeping the 2x4 clamped to the warped plywood until that joint was fully dry.
There was certainly plenty of other things that needed attention. Like yard work. Or taking the dogs to the beach :-)
Then add some more parts the next day.
The drawer slides optimally should be installed before the cabinet is assembled, but screwing straight metal slides to a warped piece of plywood is a non-starter. But the drawer slides could be installed before the cabinet back is attached, which gives much better access to the screw for the back end of the drawer slide.
I installed the drawer slides using wood spacers, instead of trying to make measurements with a tape. You can just hold the slide firmly against the spacer, use an awl to locate the drill bit, then screw. I suppose you could dispense with the drilled screw hole, but I always drill. Then use the same spacers for the other side, insuring each half of the pair of slides will be aligned.
With rain coming this week, I decided to move the incomplete cabinet carcasses into the pottery studio to allow the car to come back into the garage. Discovered the doorway into the pottery studio was a quarter-inch too narrow for the cabinets, so off came the door.
Here are the two cabinets sitting in place. The cab on the left has its back installed. The cabinet on the right needs to come out for drawer slides (need to order a couple more) and back. Then both will be shimmed, leveled, and screwed in place.
I will then need to cut out the counter-top, order and cement plastic laminate on that, and install that. Then birch trim on the front edges.
And, as always, drawers.
Wednesday, January 3, 2018
An Accidental Hiatus
And then I realize that almost everybody else lives in a house that is “finished.” Sigh.
My current unplanned break has given me a glimpse into what a “normal” life might be like. But only a peep.
My modus operandi during the almost five years I’ve been working on my whole-house remodel/renovation has been to move from one major project to the next, not always in a logical order. The last project completed was the kitchen countertop, which also enabled me to expand my daily routine with new menu items. For example, since I now have a cooktop, I can make an omelet, or cook the new generation of vege-burgers (their molecular scientist developers like to call them “plant-based burgers”). Moving toward greater normalcy, as it were — a theme this post explores.
At the end of my last post I was dismantling the gluing frame for the countertop, so clearing out my garage for the car to move back into its rightful home. I predicted that I would next be building cabinets for the pottery studio. With those built, I could buy and install the electric kiln and reengage in one of my major hobbies — that of creating (or “throwing”) pots. “Pots” includes all manner of clay creations — bowls, vases, cat dishes, etc.
Didn’t happen.
As I was preparing to order more plywood for the new cabinets, a wildfire broke out just to my south — the Lilac Fire. It grew. I spent the first day watching the continuous TV coverage. The major highway I used to get to Home Depot was closed for several days. That was the incident that began my hiatus from my major project routine — an accident, to be sure. The fire started at the side of I-15, probably when somebody threw a cigarette out a car window on that hot windy day.
So I reverted to little projects, like working on building drawers, repotting plants, cooking new menu items . . .
I saw that a couple of the gourmet chefs who are selling the new vege-burgers in their many-star restaurants were putting sliced avocados on them, and, as it happens, the avocado trees I planted now have fruit on them. But when to pick? Research required.
Avocados don’t ripen on the tree. They “mature,” and then stay good for weeks or months on the tree. But once the mature avocados are picked, they ripen within about four to eight days (and then start to go bad).
I have two trees — Fuerte and Hass. The pear-shaped Fuerte were the first commercial variety, but they have thin skins and therefore do not ship well. Hass avocados have thicker skins that tolerate being transported long distances, and so they are now the predominate commercial variety by far. Hass are oval and have bumpy skins, and mature in the spring (more or less).
Many people think the Fuerte are a bit better to eat. Fuerte mature mid-winter (this is southern California — 80˚ yesterday), so I’m starting with them. And yes, good on a burger! Or a salad . . .
Now that I was off-stride, and perhaps enjoying the break, thoughts of visiting the dog beach intruded, so off we went. (More fun than scraping old paint off overhead eves.)
And while my mind was off its remodeling rails, I explored other interests. I’ve been an electric vehicle (EV) enthusiast for more than ten years, waiting and waiting for the “perfect” EV that would last me for a long, long time. It’s actually part of the same plan as the ideal house — pursuing harmony in my life.
I have had a reservation for a Tesla Model 3 for almost two years, and while that basic car is wonderful, it has features I would have trouble living with — for example, the glass roof (here in San Diego’s intense summer sun), which would not play nice with the dogs waiting in the car, even with windows open.
My reservation for a dual-motor Model 3 will not mature until the end of 2018, in any case, and there are no other EVs coming soon that check all my boxes. So I decided I could buy an inexpensive, compromise, used EV as an interim car, so I wouldn’t have to keep driving my gasser. My gas-burner is nice enough, but not nearly as nice a driving experience as an electric car (which also charges in my garage).
More time on the internet. I discovered that 2014 BMW i3s, coming off lease, could be had for a relative pittance. The i3 was an early favorite of mine, and is a really nice EV — comfortable, good performance, responsive, and the first mass-market car to be made of light-weight carbon fiber (plus some aluminum and thermo plastic body panels). It should last forever. But it was two-wheel drive and had some quirks that put it out of contention as a “permanent” EV. The first generation had an 81-mile EPA range (sufficient for my driving), while new EVs generally go 125 to more than 300 miles on a charge. The current i3 goes about 120 miles on a charge, and by the end of the year, due to advances in battery tech, the next iteration of the i3 will have a range about double the first generation (with a battery the same size and weight).
Electric vehicles can use the magnetic forces in their motors to slow the car as easily as they accelerate it; these dual functions are controlled by the same pedal (it’s called single-pedal speed control). This magnetic braking can replace conventional friction braking 90% of the time. When slowing the car, the motor behaves like a generator and charges the battery, enhancing efficiency.
Magnetic braking only works on the wheels driven by the motor. Front-wheel-drive cars and rear-wheel-drive (RWD) cars therefore only have magnetic braking on two wheels. For the most effective magnetic braking, the EV should have all-wheel-drive, which also gives you balanced four-wheel braking.
That’s why my optimal electric car will have motors on both axles. It’s easy to put two motors in electric cars, because the motors are about the size of watermelons. All Teslas either have two motors standard or as an option, and most of the upcoming premium EVs have motors on both axles.
I’ve written a number of articles on electric cars, plus this 3-page tutorial for friends and relatives on EV single-pedal speed control (one of their best features) in case you’re interested. There's also a link on the first page of this blog.
So if the i3 and the Model 3 don’t work for me, what will? And when?
Porsche is making a very impressive EV — now called the Mission E (not the final name) — that is set for production late-2019. Camouflaged pre-production prototypes have been seen on German roads, and testing on the famous Nürburgring track. I photoshopped away the camouflage in the picture below. The AWD car checks all my boxes, and then some, but might be a little overkill for trips to the grocery store. Sigh.
But back to the house remodel.
Working on drawers at a relaxed pace. Mostly more drawers for the waterbed base, but I also built the first kitchen drawer. It’s one of the high side-loading drawers, and I’m happy with it (and looking forward to getting more of the 60+ kitchen drawers made). It’s not surprising that most kitchens have doors on most of their cabinet storage spaces, because drawers are complicated to build, and while cheap drawer slides are often used, I’m paying about $17-$18 per pair for good quality full-extension drawer slides. Soft-closing slides are significantly more.
Photos of the kitchen drawer-shelf, closed and open:
Sunday, December 3, 2017
Kitchen Countertop — Part 4
At the end of the last post, I had moved the countertop from the garage to the kitchen. To fasten it to the cabinets, I used a silicone adhesive and screws (from the bottom). After reading the directions to the silicone, I discovered I only had five minutes of open time to get the countertop clamped, so I drilled all the holes beforehand and started the screws. (It really does pay to read the directions.) Then the silicone went on.
I used three 54-pound retaining wall blocks as gravity clamps, then quickly tightened the screws (close to 20 of them).
After the silicone adhesive's 24-hour cure time, I installed the cooktop, setting it in the opening, and making the electrical connections (will be behind future drawers).
Then I used silicone caulk to fill the small gap between the sink and the countertop. I intentionally left the gap so the caulk would make a good seal.
I applied a coat of furniture paste wax to the countertop for further protection. I'll add another coat before the clutter returns.
I installed the faucet and made the water supply line connections. While all of this was going on, I had been applying three coats of epoxy to the backsplash, and sanding (same as was done for the countertop). The backsplash was installed to the wall with silicone adhesive, with a bead of silicone caulk under the bottom edge. Done!
Time for recovery. — dismantling the glue-up frame in the garage, and cleaning it all up (so the car can return). Pottery studio cabinets next.
Monday, November 27, 2017
Kitchen Countertop — Part 3
In the last countertop post, I had finished laminating the first two sections (of three) and was waiting to buy some more maple before continuing. With wood in hand, I finished laminating and planing all three sections to the same thickness. Then I carefully epoxied them together, using biscuits to keep them aligned.
I had laminated the countertop longer than it would end up so that I could make clean and square cuts on both ends. I considered doing this with a circular saw, but with the hard wood, guiding a perfectly straight cut would be near impossible. I tried, but making a test cut outside of the line (fortunately). Instead, I ended up using a router with a spiral carbide straight-cutting bit, guided with a straightedge. Worked well.
After triming both ends of the countertop, I glued the thicker edge pieces on the front and one end:
Here's a closeup of the overhanging edge piece:
Then I used the same technique that worked well to trim the ends to cut out the openings for the sink and the cooktop. Here I cut out the opening for the cooktop using a straightedge.
For the undermount sink, I had previously made a plywood template to perfectly fit the shape of the sink, and made the cut using the spiral cut bit with a template guide on the router base. After making that cut, I used a round-over bit for the edge of the sink opening.
The countertop is radiused at two of the corners. I made templates for those shapes, and used a router again to trim the countertop edges. Actually — three routers :-)
This photo shows one of the templates with the router in position:
Once the edge pieces were trimmed, I rounded over the top and bottom of the edge to form a "bullnose."
At this time, I turned the countertop over and rolled one coat of epoxy on the bottom to seal the wood (moisture barrier). Changes in moisture content of the wood (with the weather) could cause the countertop to expand or contract, or otherwise cup or move. Here's what that looked like (didn't have to be pretty):
Then after a day of curing, I flipped it back over upright and sanded until smooth. Then I rolled on the first coat of epoxy, this time using a special formulation of hardener that would ensure a clear, colorless finish. Because the various strips of wood were of different species and different hardness, they absorbed the epoxy differently. Some strips soaked it up, and with others, the epoxy stayed mostly on the surface. So the finish was uneven.
I used a random orbital sander (and 60-grit discs to start) to level everything. Then repeated after the second coat, this time sanding starting with 120-grit discs. After the third coat, the epoxy was very glossy, but not completely flat, and I was not able to get rid of all the bubbles and bits of grit during the application process. But the gloss brought out the color in the wood.
I continued to use the random orbital sander, with finer grits, finally up to 220-grit after the fourth coat. The surface was getting to be quite flat; the dry sanding left white epoxy dust.
I had considered leaving a high gloss on the countertop (assuming I could get apply a perfect topcoat), but decided the gloss would show scratches and other blemishes. So I decided on a satin finish, that could be had by sanding. That also had the advantage of producing a flatter, glass-smooth surface. So after the last 220-grit sanding, I started to wet-sand by hand, first with 320-grit, then 400, then 600, and finally using 800-grit paper. The water lubricates the fine paper, keeping it from clogging. You can also see when you are removing the top layer of epoxy by the white slurry that is produced.
After the 800-grit, I was happy with the surface, and carried the countertop inside to test fit it on the kitchen cabinet. It fit, happily.
I may apply furniture wax at some point. But next I have to attach it to the cabinet using screws from the underside, along with silicone adhesive. Then I will finish and install the matching laminated backsplash. Then install the faucet and the cooktop. Those steps will be the subject of my next post.
This is an arid climate (we've had no measurable rain since last spring), so I provide the birds with clean water in my front and back yards. A recent large visitor (on a hot day), sat on the edge of one of the water bowls (occasionally drinking) for 15 minutes before flying off.






































